The passive film behind stainless steel: patents, measurements, and corrosion
The passive film protecting stainless steel is thin enough to measure in nanometers, yet it shields the metal beneath. Chromium in the alloy allows a chromium-rich oxide layer to form naturally at the surface. The British Stainless Steel Association describes a typical thickness of 1–5 nanometers and emphasizes the need for sufficient oxygen. This is a protective surface condition, not an assurance that corrosion cannot occur. Early patents pursued resistance to tarnishing in knife blades; later experiments measured the actual film and how its behavior changed with the surrounding solution.
Harry Brearley's U.S. patent 1,197,256, granted on September 5, 1916, was titled Cutlery. It described hardened, polished blades made from an iron alloy containing chromium and controlled amounts of carbon. One claim specified approximately 13% chromium, 0.30% carbon, and 0.30% manganese. Brearley connected the desired performance to both composition and treatment: the blade was formed, hardened, tempered, and polished. The familiar object was a knife, but the material prescription was much more particular than a shiny finish or the word stainless stamped on a handle.
Brearley described his product as practically untarnishable under ordinary knife use. He also reported limits from his experiments: steels with less than 8% chromium were relatively tarnishable, and excessive carbon was associated with visible free carbides and loss of the desired resistance. These statements belong to his patent's description of particular steels and processing. They are not today's definition of every stainless grade. The document presents a manufacturing proposal and claimed performance; it supplies neither a measurement of film thickness nor a promise of survival in every acid or salt solution.
Elwood Haynes's patent 1,299,404, granted on April 1, 1919, pursued a related combination of a durable polished surface and a useful cutting edge. He favored an iron-chromium alloy with low carbon and described compositions containing 20–25% chromium and 0.1–0.5% carbon. His discussion of manufacturing warned against contact with carbon during melting and recommended alumina vessels. Workability mattered alongside resistance: the material had to be forged, hammered, or otherwise shaped into useful tools. The patent extended the proposed uses to utensils and other implements, rather than treating surface appearance as the sole requirement.
The modern mechanism explains why chromium has that special place. BSSA's guidance describes the passive film as strongly attached and chemically stable under suitable conditions. If it is damaged, it normally forms again when enough oxygen reaches the surface. Its description of the BS EN 10088-1 classification specifies at least 10.5% chromium by weight and no more than 1.2% carbon. Other alloying elements can adjust corrosion resistance and mechanical properties. A scratch therefore need not permanently remove protection, but the surrounding conditions must allow the protective surface to return.
In 2019, Rongguang Wang and colleagues measured a passive film while stainless steel remained in liquid. They deposited a small gold patch on a polished SUS304 specimen to provide a reference height. Dilute sulfuric acid removed the original film; after washing, water allowed a new layer to form. Atomic force microscopy compared the steel's surface height against the gold before and after that change. The observed thickness in water was 4.85 nanometers. The method followed removal and regrowth rather than inferring an invisible barrier solely from the metal's resistance to rust.
That value was not a universal thickness. The same investigation found that measured film thickness varied with acidity and chloride concentration, increasing with higher pH and with fewer chloride ions. The film also appeared thicker in water than under vacuum. The authors attributed that difference to hydroxyl groups and absorbed water associated with the film in liquid. The passive film was therefore sensitive to both its environment and the conditions of measurement. A number obtained after taking a specimen out of water did not necessarily describe the surface while it was immersed.
A bolted joint or gasket can create a much less favorable environment than an open surface. BSSA's guidance on crevice corrosion describes liquid entering a narrow gap and becoming stagnant. Oxygen inside can be consumed faster than it is replaced. Metal ions accumulate, chloride ions can migrate inward, and reactions produce an increasingly acidic local solution. At a sufficiently low pH, the passive film can fail locally and corrosion can continue within the crevice. The metal outside that small region may still appear protected.
This also explains why alloy selection cannot substitute for attention to the joint. BSSA identifies molybdenum and nitrogen as additions that increase crevice-corrosion resistance, while advising open junctions, sound welds, and control of surface deposits. Even an insulating gasket can leave a crevice between metal and nonmetal surfaces. The vulnerable feature is the sheltered local chemistry, not simply electrical contact between two metals. BSSA also notes that crevice attack can begin at chloride concentrations lower than those needed to initiate pitting on a free surface.
- British Stainless Steel Association — When is stainless steel passive or active: formation of the passive layer — bssa.org.uk
- Harry Brearley — U.S. Patent 1,197,256, Cutlery (September 5, 1916), specification and claims — patents.google.com
- Elwood Haynes — U.S. Patent 1,299,404, Wrought-metal article (April 1, 1919), specification and claims — patents.google.com
- Wang et al., Scientific Reports 9, 13094 (2019) — Using Atomic Force Microscopy to Measure Thickness of Passive Film on Stainless Steel Immersed in Aqueous Solution — www.nature.com
- British Stainless Steel Association — Principles and prevention of crevice corrosion — bssa.org.uk